Category: 3D Printing


3D Printing Time Lapse – Gecko DeskPal Fridge Magnet Remix

By ChunkySteveo,

A remix of a great little Gecko model to be used as a fridge magnet. One of my kids loves putting things on the fridge, and loves my super strong neodymium magnets, and loves 3D printing, so I combined the lot in this remix! She even helped with the measuring of the magnet using my  … Read more

P3Steel Build Log (#08) – Y-axis Rod Stops

By chunkyadmin,

Either by fault of my own or tolerances in the steel rod or frame after successfully wiggling and inserting the rod, they did not fit snug and were not tight enough, This caused the rods to move as the print bed went back and forth. I did not want any possible movement in the rods, so investigated Thingiverse for a simple clip bracket to hold the rods in place at each end. A couple of minutes later and there was a simple little bracket design by user Hobsie which looked perfect and resolved the issue.

P3Steel Build Log (#07) – Y-Axis Carriage and Belt

By chunkyadmin,

Y-Axis Carriage Now that the clamps are sorted it’s time to fit them to the blank y-carriage, as seen below. The 2.5 DXL frame uses four points to fasten bearings, some holes in the middle for the y-axis belt tension block and the bed screws holes at each corner. The middle “sticky-outy” part seen below  … Read more

P3Steel Build Log (#06) – Y-axis Carriage Clamps

By chunkyadmin,

Bronze Bushings or LM8UU Bearings The standard Prusa builds (and most other 3D Printers, CNCs, engravers etc) use LMU88 linear bearings for all linear rod movements. They are the go to part when you use 8mm smooth rod as your axis guides and are cheap, easy to use and readily available. The quality of these  … Read more

3D Printing Time Lapse – Ball-joint Articulated Octopus Keyring REMIX

By chunkyadmin,

A neat little model to print and make from Thingiverse. I want to print the original full size Articulated Octopus, but for now I found this remix which is a keyring. Printed on my Printrbot Simple 3D Printer and recorded on the time lapse function of my Octoprint Octopi print server installed on a Raspberry Pi.

3D Printing Time Lapse – Raspberry Pi Zero Case + v1.3 REMIX

By chunkyadmin,

I was in need of a case for my Raspberry Pi Zero so looked around on Thingiverse for a suitable one. I wanted a simple case with no mechanical fasteners, just something to protect it and have easy “snap on” parts. I went with the model by cfunseth on Thingiverse, but soon realised it wouldn’t  … Read more

P3Steel Build Log (#05) – Frame Feet

By ChunkySteveo,

The steel frame of the P3Steel could easily scratch up any surface it sits on, and vibrations and movement may be translated down through it’s legs. I am building the printer on a table, so was very aware of scratching it(!) A look on Thinkgiverse shows a lot of different feet for the printer, but  … Read more

P3Steel Build Log (#04) – Y-Axis Motor And Idler

By ChunkySteveo,

Part of the frame assembly (or just after) is to fasten the y-axis motor mount and belt idler. They sit either side of each other at the two ends of the printer frame. This is where this 3D printers starts it’s path away from the standard version and takes on Toolson’s upgraded and improved parts.

P3Steel Build Log (#03) – Main Frame Assembly

By ChunkySteveo,

With the frame painted and dry, first thing to do is bolt together the main structure. It slots together like a jigsaw and there was absolutely no issues or problems in this process. All the bolts and nuts used to secure the main frame parts are M3 bolts and nylock M3 nuts. The RepRap Wiki suggests  … Read more